Leaving the flue open overnight is generally safe, especially if there is a fire burning. However, it can lead to heat loss and may not be necessary once the fire has extinguished. Flue pipes should be properly sealed with high-temperature tape or sealant to prevent leaks and ensure efficient venting. In some cases, adjustable flue dampers allow for partially closing the flue to control draft. However, it is essential to follow the manufacturer’s recommendations and ensure adequate draft for safe venting.

Typical flue sizes for residential appliances can range from 2 inches to 8 inches in diameter, depending on the BTU output of the appliance and the type of fuel used. Flue pipes should have a slight upward slope from the appliance to the vent termination to prevent condensate buildup and aid in proper draft. The angle of a flue pipe should have a minimum upward slope of 1/4 inch per foot to promote proper venting. Tees - Used at the rear of an appliance with horizontal outlet and to be used in conjunction with separate stainless steel tee cap that clips on and off for cleaning and inspection purposes. Adjustable Flue Pipes - A variety of telescopic lengths. The band is tightened to secure the joint, this item is non-load bearing and support must be providedimmediately above the adjustable pipe.Yes, it is generally recommended to close the flue when the appliance is not in use to prevent heat loss and drafts. In summer, when the appliance is not in use, it is generally recommended to close the flue to prevent heat loss and avoid drafts. A flue pipe can be too large if it exceeds the manufacturer’s recommendations for the appliance’s BTU output and flue height. An oversized flue can cause draft problems and reduce efficiency. New Swept Elbow - This is the latest product to be added to our Premier Flue Pipe range. Outstanding performance and efficient gas flow are only two of its features. It is aesthetically pleasing and easily cleaned which are important factors when choosing for domestic appliances. Available in 5" and 6"diameters and three angles 90°, 110° and 135°. Also available with an optional blended door for ease of cleaning.

Flue Direct is built on our reputation, excellent delivery times, unbeatable prices and advice service. Please ensure that your goods have arrived before booking your installation service. If you have any queries please feel free to get in touch.

You may also be interested in the following product(s)

The size of the flue pipe for a 50-gallon water heater depends on the BTU rating of the water heater and the height of the flue run. Consult the manufacturer’s guidelines for the appropriate flue size. The 2-10 rule for chimneys is similar to the 3-2-10 rule and refers to clearance distances required between a chimney and nearby structures. The chimney should be at least 2 feet higher than any roof within 10 feet horizontally. Our Flexible flue liner is available in both 316 grade stainless steel and 904 grade (Lifetime warranty). Both are suitable to reline your chimney for use with a multi fuel stoves and wood burners and are HETAS approved, for further information please refer to the flexible flue liner section. To improve flue draft, ensure proper installation, minimize bends, keep the flue clean, and maintain adequate combustion air supply. It is essential to follow the manufacturer’s guidelines. The size of the flue you need depends on the type of appliance you are venting, the fuel used, and the manufacturer’s recommendations. Generally, flue size is determined by the BTU output of the appliance and the length of the flue run.

Premier Flue is a comprehensive range of Vitreous enamelled flue pipe. Manufactured in accordance with ISO9001-2008 using superior grade low carbonsteel and coated to the highest standard. Suitable for oil, gas and Solid Fuels, for domestic heating appliances. Finished productshave an internal and external vitreous enamel coating to offer extremely high resistance to heat and toxic or corrosive gasses meeting with the requirementsof BSEN ISO 28706 - 1:2011. What size flue do i need? HETAS regulations state that there is a minimum flue size of 150mm / 6 inch for any stove (on which wood could be burnt) unless it is Defra Exempt. Therefore, you may need to increase your flue size from your stove outlet using an increaser e.g 5 – 6 inches. Please talk to us for further information if required. The length of a flue pipe can vary depending on the appliance’s BTU rating, the type of fuel used, and the manufacturer’s guidelines. It is essential to follow their recommendations. Leaving the damper open overnight is generally safe if there is a fire burning. However, it can lead to heat loss and is not necessary once the fire has extinguished.The size of the exhaust for a gas water heater depends on the BTU rating of the water heater and the manufacturer’s guidelines. Common sizes include 3 inches and 4 inches in diameter. An open flue can allow significant heat loss, especially in cold weather. It is recommended to close the flue when the appliance is not in use to prevent heat loss.

A flue can go straight up if it meets the necessary clearance requirements and local building codes. However, the height and construction of the flue must follow the manufacturer’s guidelines. For a water heater, the size of the chimney liner depends on the BTU rating of the water heater and the height of the chimney. It is essential to follow the manufacturer’s guidelines or consult a professional to determine the appropriate size.

Details

The minimum width of a flue depends on the appliance’s BTU output and the type of fuel used. It is essential to follow the manufacturer’s recommendations.